11. Citizen Cincom E32 IV G Codes M Codes

Citizen Cincom E32 IV G Codes M Codes

 
Citizen Cincom E32 IV G Codes & M Codes for cnc machinists programmers.

G Codes

G Code Function
G00 Rapid Feed
G01 Linear Interpolation
G02 Circular Interpolation (Clockwise)
G03 Circular Interpolation (Counter Clockwise)
G04 Dwell
G28 Reference Point Return
G32 Thread Cutting
G50 Coordinate system setting
G90 Longitudinal direction turning cycle
G92 Thread cutting cycle
G94 Face turning cycle
G96 Constant surface speed control
G97 Constant surface speed control cancel
G98 Per minute feed
G99 Per rotation feed

G Code Macros

G Code Function
G201 Product separate command
G210 Y axis machining mode ON (E32IV only)
G211 Y axis machining mode OFF (E32IV only)
G500 Coordinate system shift OFF
G501 Coordinate system shift ON
G710 Twin turret command
G711 Select turret No.1
G712 Select turret No.2
G720 Two-saddle machining command
G721 C axis cross cancel
G722 C axis cross command
G730 Back/front simultaneous machining command
G740 3-Line simultaneous machining command
G750 Pick off, center support machining command
G999 Last program execution

Special G Codes

G Code Function
G12.1 Milling interpolation (Option)
G13.1 Milling interpolation cancel (Option)
G113 Spindle and tool spindle synchronization cancel (It is an option except for E32IV)
G114.1 Spindle synchronization (Option)
G114.2 Tool spindle synchronization I (It is an option except for E32IV)
G114.3 Tool spindle synchronization II (It is an option except for E32IV)
G115 Start position queuing (Type 1)
G116 Start position queuing (Type 2)
G117 Miscellaneous command output during axis move
G125 Control axis synchronization
G700 Cancel machining command

M Codes

M Code Function
M00 Program stop
M01 Optional stop
M02 1 cycle stop (Stop the machine when under the 1 cycle mode.)
M03 Spindle forward rotation
M04 Spindle reverse rotation
M05 Spindle stop
M06 Chuck close
M07 Chuck open
M08 Short cut program insertion ON (Starts the end cut program of bar material)
M09 Short cut program insertion OFF (Ends the end cut program of bar material)
M10 Knock out ON (Forward move of back side knock out bar)
M11 Knock out OFF (Reverse move of back side knock out bar)
M13 Close ling workpiece chuck
M14 Open long workpiece chuck
M15 Close back chuck
M16 Open back chuck
M18 Spindle zero point return and C axis gear ON (Preparation for C axis control)
M20 Reset C axis selection (End of C axis control)
M23 Back spindle forward rotation
M24 Back spindle reverse rotation
M25 Back spindle stop
M31 Turret speed selection (low-speed swing)
M32 Forward move of workpiece separator (back side)
M33 Reverse move of workpiece separator (back side)
M46 Y axis clutch OFF (Allows the axis move)
M47 Y axis clutch ON (It must not be used except when Y=0)
M50 Back pick-off inferiority detection (Rotate the spindle at low speed to set M50 after cut-off)
M51 Tool break detection (Detects the tool by the switch)
M52 Coolant ON
M53 Coolant OFF
M54 Bar feeder stop (Used when replacing the material.)
M55 Bar feeder material replacement start (Starts replacement of the bar feeder material.)
M56 Product count
M61 External M code 1
M62 External M code 2
M63 External M code 2
M64 External M code 4
M65 External M code 5
M72 Back spindle air blow ON
M73 Back spindle air blow OFF
M74 C axis zero point deceleration dummy timer (to be used with M74G28H1;)
M75 Back spindle torque control (L) ON (25% the rated torque (same as M123))
M77 Waiting for spindle synchronization to end
M78 Back spindle indexing
M79 Back spindle indexing OFF
M80 Tool #1 spindle forward rotation
M81 Tool #1 spindle reverse rotation
M82 Tool #1 spindle stop
M83 Tool #2 spindle forward rotation
M84 Tool #2 spindle reverse rotation
M85 Tool #2 spindle stop
M88 Interference check OFF (reset)
M89 Interference check ON
M94 Back spindle variation detection ON
M95 Back spindle variation detection OFF
M96 Spindle variation detection ON
M97 Spindle variation detection OFF
M98 Subprogram call
M99 Program return
M123 Back spindle torque limit (H) ON (When cut-off with the spindle and back spindle synchronization with each other. To stop the workpiece to slip in the chuck by the rotation error.)
M124 Back spindle torque limit OFF
M125 Citizen side used within the macro.
M126 Citizen side used within the macro.
M127 Citizen side used within the macro.


-------------------------
  1. Denford Mirac PC CNC Lathe G & M Codes
  2. Andron Andronic 2060 G Codes & M Codes
  3. G & M Codes AMADA AE255NT AE2510NT CNC Turret Punch Press
  4. C.B.Ferrari E560 Machining Centers M Codes
  5. C.B.Ferrari E560 G Codes
  6. Makino Pro 3 Program Protection
  7. GTCNC-150iT-II G Codes M Codes 
  8. GTCNC-60TT G Codes M Codes 
  9. GTCNC-150iM-II G Codes M Codes Program Instructions
  10. Mori Seiki G Codes and M Codes 
  11. Citizen Cincom E32 IV G Codes M Codes 
  12. Makino Pro 3 M Codes (Fanuc 16i/18i)
  13. Makino Pro 3 G Codes (Fanuc 16i/18i)
  14. Cincinnati G-Codes & M-Codes – Acramatic 2100e
  15. Bosch CC 220 Manuals, Bosch CC 120 100 Manuals Free Download
  16. Bosch CC 100 M G-Codes and M-Codes
  17. Bridgeport G Code List – CNC Mill
  18. ProtoTRAK Manuals Download Safety, Programming, Operating & Care